-
product
Cable Tester
KT-45
Quickly test twisted cable RJ45 and BNC connector including T568A/B, 10-Base-T (UTP/STP), Token Ring, etc. Automatic test for open circuits, shorts, reversals, miswires, continuity. Main unit and one remote allow one person to test. Includes protective leather pouch. Testing before and after installation
-
product
AstroAI Multimeter
2000
AstroAI Multimeter 2000 Counts Digital Multimeter with DC AC Voltmeter and Ohm Volt Amp Tester ; Measures Voltage, Current, Resistance; Tests Live Wire, Continuity
-
product
Digital Multimeter
DT-9205B
3 1/2 digits LCD with max reading of 1999Automaticnegative polarity indicationFull range over load protectionDiode&HEF test; Continuity test
-
product
Electrical Tester For Voltage
PDT35
Automatically Selects VAC, VDC, or Continuity TestComplies with EN 61010-1 For Use in CATIII 600 V Environments1999 Count LCD DisplayAuto Power On/OffHigh Input Impedance -- 400 kVoltage AC: Max Range 600 V, Accuracy +/- 1.5%Voltage DC: Max Range 600 V, Accuracy +/- 3.0%Continuity TestAccessories Included: Test Leads, 2 'AA' BatteriesDimensions: 8.46' H x 2.83' W x 1.44' DWeight: 8.29 oz.Sold as : Unit
-
product
MATCO TECH MULTIMETER
MD257
*Provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests*Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
product
Clamp Meter AC Current 1999 Counts
VA310 VA310C
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Diode Test Back Light Continuity Buzzer.
-
product
Bench Digital Multimeter, 40000 Count, True RMS, Auto, Manual Range, 1 kV, 10 A, 4.75 Digit
72-1020
This unit measures AC/DC voltage and current, resistance, capacitance, frequency, and temperature. It also provides diode and audible continuity test, as well as 4~20mA loop testing.
-
product
2 in 1 LAN Tester
PLTM20
Tests Pin Configuration for 10 Base-T, 10 Base-2, RJ45/RJ11, 356A, TIA-569A/568B and Token Ring CableRemotely Test Cables Up to 330 Yards AwayTest Ground WireMeasure DC/AC Voltage, DC/AC Current, Resistance, Continuity, and DiodeDC Voltage: Max Range 600 V, Accuracy +/- 0.5%AC Voltage: Max Range 600 V, Accuracy +/- 1.2%DC Current: Max Range 200 mA, Accuracy +/- 1.2%AC Current: Max Range 200 mA, Accuracy +/- 2.0%Resistance: Max Range 20 M, Accuracy +/- 0.8%Continuity Test: Beeps If Less Than 100 Accessories Included: Test Leads, LANtest Remote Terminator, 9V Battery, Carrying CaseDimensions: 6.38' H x 2.93' W x 1.73' DWeight: 10.86 oz.Sold as : Unit
-
product
MIPI Validation License Suite
SW00MIPI
The MIPI Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for MIPI with coverage across the MIPI technologies M-PHY, D-PHY and C-PHY. Together with the subscription model, this enables the support and coverage continuity as the MIPI technology progresses through revisions.
-
product
Network Cable Tester
KT-96A
LCD Max. Indication 3999,with length unit. Locate the broken point of a cable. With RS-232 interface, it can be connected to your computer. Takes a new ¡°VECTOR MEASUREMENT¡± technology in measuring the length of the cable. Length Test Range:400m/4000m/40km. Accuracy: ¡À1% rdg ¡À 0.3m. For use in computer network, CATV, communicate engineering. With Volt, Resistance,continuity,diode test
-
product
Auto-Ranging Digital Clamp Meter
DCM401
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
product
Compact Digital Multimeter
MT-1705
1/2 digits 1999 counts.0.5% best accuracy.CAT III 600V safety rated.Auto polarity indication.AC True-RMS for accurate measurements.Large backlight LCD display for easy reading.Extra Functions: Continuity with beeper, Diode test, Data hold, Auto power off, Low battery indication, Overload indication, LCD backlight,Frequency and Capacitance are auto rangeIdeal for wide variety of electrical and electronic testing applications.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
Hose Continuity Tester
OhmGuard
The OhmGuard hose continuity tester is designed to test hoses used on vacuum trucks and tanker trucks prior to the transfer of flammable or combustible products
-
product
Autoranging Digital Multimeter w/Bargraph
HH2209
High Accuracy (Basic Accuracy 1.0%)Jumbo LCD display 3260 count, 21mm figure heigh with BaragraphAuto Ranging or Manual Ranging at your choiceHigher Voltage test up to AC 750V and DC 1000VHigher Current test up to 20AResistance test up to 30MΩTemperature test range from -4oF or 1832oFWide Frequency test range up to 300kHzDiode test, audible continuity check and Transistor testLow Battery Indication
-
product
Manual Ranging Digital Multimeter
HH3502
Double Injection Casing. High Accuracy (basic accuracy 0.5%). 3-1/2 digit Jumbo LCD display 2000 count with symbolic signs and back light. Manual Ranging High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 20A AC/DC. Transistor test. Diode and Continuity check. Measure Resistance up to 20MΩ
-
product
Pro-Level Manual Digital Multimeter
HH2205G
High Accuracy (Basic Accuracy 0.50%). 3-3/4 Jumbo LCD display 4000 count with symbolic signs. Double Injection Casing. Backlight for work in a dim area. High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 10A AC/DC. Diode and Continuity check
-
product
Insulation & Multifunction Tester (LCD Display)
4153 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Insulation Resistance, voltage (AC-DC) measurements with automatic hold facility, diode, ohm, and continuity with a short circuit current of minimum 220mA.● Auto-off function.● Energy conservation feature.● Ener-Save™ limit the test duration to about 10 Seconds.● Quick Test and EnerSave™ are unique features. Both saves energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Operates with rechargeable batteries, alkaline or low cost general purpose batteries.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
product
Cable Testing Service
Cable testing service available from Cimbian includes:Helping you with the test specificationBuilding the test interface, where necessaryCreating the test programBarcodingTest reportsSimple continuity testingMeasurement/verification of resistances and diodes (traceable to national standards)Hi-Pot testing to 1500VDC / 1000VAC
-
product
Continuity Testers
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
product
Digital Clamp Tester (CE)
M-2010
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Data-hold and Auto power off function.*Conform to IEC safety requirements.*Additional AC/DC voltage, resistance, diode test, continuity check.
-
product
Digital Multimeters
The Gamma series consists of digital multimeters. They are capable of measuring electrical parameters like current, voltage, frequency, temperature, resistance, diode test and continuity test of the circuit respectively.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
DDR Validation License Suite
SW00DDRV
The DDR Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for DDR with coverage across the DDR technology starting from DDR3. Together with the subscription model, this enables the support and coverage continuity as the DDR technology progresses through generations.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
DC/AC Clamp Meter
KT-9050
3 2/3 digits LCD with max. reading of 2500AC/DCA, AC/DCV measurementResistance test, Diode test, Continuity beeper Data hold function, Relative testAuto range,auto power offHand guard protection meet IEC1010 safety requirementsSmall size, Light weight
-
product
AC Hipot Tester
298
Our Model 298 is a simple-to-use 500VA AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 298 500VA AC Hipot Tester includes all the features you need to get the job done and move on.
-
product
Cable Testers
E445
Tests 3 pin XLR leads, 2 and 3-pole A-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
product
Stick Meters
Stick Meter and is packed with the portability, toughness and modular expandability HVACR professionals expect. This slim-shaped digital multimeter fits easily in your pocket or on your belt in the included case. Features most of the electrical parameters you use everyday including microamps DC for flame rectifier diode tests and capacitance for motor-run and motor-start capacitors. It’s a manual ranging meter and features a rugged ABS plastic housing with an O-ring to block contaminants, MAX hold, hi-voltage and continuity LEDs and beepers, and auto power-off (APO) to conserve battery life.
-
product
Voltage/Continuity/Phase Rotation Tester
CZ20060
The CZ20060 is the classic 2-pole tester ideal for quick and easy GPO testing and voltage measurement. Sold to electricians and contractors worldwide, the CZ20060 is a tried and tested, proven tool, rugged enough to withstand everyday use. With ranges between 12V - 690V and both LED and LCD display all your basic requirements are covered. Phase rotation and continuity measurement are included to complete test functionality.
